Disconnect the LVDS cable. Battery release Releases the battery for removal. Run the speaker cable along the channel. Palmrest Comfortable support area for your hands when you use the computer. Sound Problems, Microphone Problems Sound Problems If sound problems are experienced, perform the following actions one at a time to correct the problem. Slide the battery lock in the direction shown to release position 1 , insert the battery pack and secure the battery in place.
|Date Added:||16 March 2011|
|File Size:||28.59 Mb|
|Operating Systems:||Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X|
|Price:||Free* [*Free Regsitration Required]|
Secure the one 1 securing screw on the Right Speaker Module. Place the CPU on a clean, dry surface when it is not installed. Pre-disassembly Instructions Pre-disassembly Instructions Before proceeding with the disassembly procedure, make sure that you do the following: Remove the DIMM module.
Remove the six 6 securing screws three on each side from the LCD Panel brackets. Remove the LCD assembly from the lower cover. Pry the antenna assembly clear of the device. Connect C as shown. Removing the Right Speaker Module 1. Replacing The Mainboard Replacing the Mainboard 1.
Select Boot Devices to select gateway nv55c network controller devices to support boot. Starting at the top right side of the cover, pry apart the Upper and Lower Covers as shown. Gateway nv55c network controller the Speaker cable along the cable channel. Your metwork is already properly configured cojtroller optimized, and you do not need to run this utility. Ckntroller back the foil tabs and remove the cable from the cable channel.
Gateway notebook user’s guide – traditional chinese 98 cntroller. Pre-disassembly Instructions Before proceeding with the disassembly procedure, make sure that you do the following: Removing the SIM Card 1. Page Appendix C Why should I update drivers? Remove the white antenna from gateway nv55c network controller hinge channel.
Gateway Drivers Download Center
Boot This menu allows the user to decide the order of boot devices gateway nv55c network controller load the operating system. NOTE Gives bits and pieces of additional information related to the current topic. Run the black antenna cable along the cable channel. If the device displays a down arrow, right-click on the device and click Enable. Chapter 4 Troubleshooting Common Problems Use the following procedure as a guide for computer problems.
Enter text from picture: Remove the eleven 11 screws on the lower cover and five 5 gateway nv55c network controller from the battery bay.
Replacing the 3G Module 1. Run the advanced diagnostic test for gateway nv55c network controller system board in loop mode at least 10 times. Lock key Description Caps Lock Open the locking latch controler disconnect the FPC from the mainboard. Place the microphone set in the panel. The outside housing and color may vary from the mass produced model. Removing the Antennas 1. Remove the two 2 bezel screw caps and screws. Slide the battery lock in the direction shown.
The pins on the underside of the CPU are very delicate. Run the cable gateway nv55c network controller the channel in the LCD Module as shown.
Gateway Drivers Download – Gateway
Place the Upper Cover on the Lower Cover as shown. How to Update Gateway Drivers? Flash is complete when the message Flash programming complete displays. Connect the bluetooth to mainboard cable. Remove the black antenna from the cable channel.
Run the cable along the cable channel and fold over the foil tabs to secure the cable in place. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, nv5c5 any form or by any means, electronic, mechanical, magnetic, contrroller, chemical, gateway nv55c network controller or otherwise, without the prior written permission of Acer Incorporated.
Gateway nv55c network controller one 1 screw on the 3G Cover. Unlock the mainboard to card reader cable connector. Do not replace a non-defective FRUs: Pass the cable through the upper cover as shown.
GATEWAY NV59C SERIES SERVICE MANUAL Pdf Download.
Place the LCD Panel in the module. Secure the eleven vn55c screws on the lower cover and four 5 screws from the battery bay. Connect B as shown. Line up the right edge of the 3G gateway nv55c network controller and replace. Select the desired boot sequence by entering the corresponding sequence. Got it, continue to print. Replacing the Hard Disk Drive Module 1.